A homemade macramé dream catcher

#v15878

Make your own dream catchers by braiding different designs in different sizes using the macramé technique. Here we are showing two variants made using simple techniques.

#v15878
Select products for the idea

{{ optionsGroup.label }}

{{ getVariantsButtonText(option) }}
   
 
 
   
 
 
   
 
 
   
 
 
   
 
 
Total price
{{ getFormattedBundlePrice() }}

{{ getRewardMessage() }}

Guide step %d
1   Make a dream catcher with a stringent design by cutting 13 x 3 m pieces of cotton twine for a 25 cm diameter ring or cut 13 x 2 m pieces of cotton twine for a 20 cm diameter ring. Tie a doubled-over piece of cotton twine onto the ring and secure it at the opposite side by twisting each cord around the ring and then tying a knot as shown in the photo. You will braid around this doubled over cord.
Guide step %d
2   Tie the doubled-over cords onto the top of the ring and feed the ends behind the previous cords. Tie a double knot with a cord from each side. Pull the cords downwards at an angle and tie them onto the sides of the ring as shown in the photo.
Guide step %d
3   Continue with all the 12 pieces of cotton twine so that there are 6 cords on each side of the doubled-over twine in the middle. Tie a double knot with the cords that cross behind the previous cords and then tie the ends onto the side of the ring right underneath each other as shown in the photo.
Guide step %d
4   Secure the last cords straight down by twisting around the ring once and tying a knot. Adjust the knots so that the cords are spaced equally.
Guide step %d
5   For the large leaf: Cut 20 x 14 cm pieces of cotton twine. Double them over and tie them onto one of the middle cords in pairs as shown in the photo. For each of the two small leaves cut 14 x 10 cm pieces of cotton twine and make leaves around the two outer cords following the same procedure.
Guide step %d
6   Unravel the cotton twine with a comb. Trim into a leaf shape using a pair of scissors. A tip: Make the cotton twine leaves wet and put them under pressure to get a beautiful shape.
Guide step %d
7   Thread wooden beads onto the long pieces of cotton twine which are hanging down from the dream catcher.
Guide step %d
8   Trim the long pieces of cotton twine into a pointed shape at your chosen length. Unravel the lowest 5 cm with a comb.
Guide step %d
9   Make a dream catcher with a classic design by cutting a 1 x 2.5 m piece of cotton twine for a 15 cm diameter ring. Divide the ring into 8 sections, 5.5-6 cm long and mark each with a pencil. Tie the cotton twine onto one of the pencil marks and twist the twine around the ring. Cross in front of the twine before securing the twine onto the ring at the next pencil mark as shown in the photo.
Guide step %d
10   Continue wrapping the twine tightly around the middle of the next piece of cotton twine all the way around and cross in before the next round. Continue until the pattern reaches the middle of the ring. Tighten as you go along and hold onto the last knot with your index finger and thumb whilst making the next knot. Finish by making a knot on either side of a wooden bead. Apply a small blob of glue onto the very first knot and the last knot. Trim the twine closely.
Guide step %d
11   Here is a 15 cm diameter ring with a classic dream catcher pattern.
Also go exploring in
Go back
I'm shopping as
Continue as guest
Your benefits of login

✔ Your personal wishlist

✔ See your order history

✔ Easy checkout
Your benefits of login

✔️ Your special prices

✔️ Special B2B products

✔️ B2B marketing universe
Your benefits of login

✔ Content especially for you

✔ Your special prices
Copyright © 2021-present Magento, Inc. All rights reserved.